-
Armed Mounted Manifold
Arm Mounted Manifolds provide a compact, turn-key solution for powering a range of end-of-arm tools, offering solutions for gripper actuation, suction cup activation, and venturi generation and measurement, these manifolds are engineered to help your Universal Robot perform a variety of tasks.
Please Login to see the price -
Automatic Pneumatic/Electric Clutch
The clutch provides mechanical, pneumatic, and electric connections and is ready for full autonomous tool changing with all options available. The automatic electric clutch consists of one robot master electric, two tool holders electric, and two tool pockets.
Please Login to see the price -
Dual Gripper Mount
The Dual Gripper Mount allows for the simultaneous mounting of two end-of-arm-tools on one robot wrist. Supporting a range of customer-configurable flange sizes, it is a time saving device that optimizes a single robot.
Please Login to see the price -
Dual Quick Changer
The Dual Quick Changer enables you to use our end-of-arm tools together in a single cycle. With this innovative solution, you can use two RG2 grippers or an RG6 gripper with a VG10 – it’s entirely up to you. Quickly and seamlessly switch between our tools to maximize the utilization of your robots with the Dual Quick Changer.
Please Login to see the priceDual Quick Changer
Please Login to see the price -
Electric Clutch
Electric clutch is a good option for tool changing in all applications where you need electric and pneumatic connections. To achieve the full autonomous tool changing system, you can upgrade by adding tool pockets. The pneumatic and electric clutch consist of one robot master electric and two tool holders electric.
Please Login to see the price -
Light Manual Clutch
Light manual tool changer is only for mechanical tools without pneumatic and electric connections. It is still possible to have electrical or pneumatic tools mounted but tools need to be connected bypassing the clutch. The light manual clutch consists of one robot master light and two tool holder lights.
Please Login to see the priceLight Manual Clutch
Please Login to see the price -
Manifold Pneumatic
The pneumatic manifold is an optional tool attached on the SMARTSHIFT Tool holder when air is needed in vacuum applications, and the application requires the air to be routed out on the sides of the tool.
Please Login to see the priceManifold Pneumatic
Please Login to see the price -
Manual Clutch
The Tool holder is a good introduction to the SMARTSHIFT products, as it permits all the possible connections. The manual pneumatic clutch is ready for easy mounting and tool changing in all applications, where you need a pneumatic connection. This solution provides the option for electrical connection and for future upgrades to an automatic solution where a tool pocket is possible. The pneumatic clutch consists of one robot master and two tool holders.
Please Login to see the price -
Manual Tool Changer Low Profile
The Millibar Manual Tool Changer is a natural fit for research labs. Designed for high-mix, low volume production environments, researchers can effortlessly change end of arm tools, or move a tool between different robots, without tools, in seconds. Simply release the locking lever and slide a new tool into place.
Please Login to see the price -
Manual Tool Changer Utility
Utility Series Quick-Change Manual Tool Changer with dual pneumatic pass and 8 pin electrical pass through. Pass 24 VDC signals from sensors and switches on your EOAT back to the robot controller. Tool changer mounts directly to the tool flange with no adapter plate required. For rapid EOAT deployment, choose from 6 pre-engineered tool sides with no adapter plates required. Change tools and break air/ vacuum connections in seconds simply by releasing the locking lever and sliding a new tool into place.
Please Login to see the price -
Nordbo Active Compensation unit
The Nordbo Active Compensation unit (NAC) assures a constant applied force, regardless of the complexity of the surface curvature, processing speed, and orientation of the tool. Sensors inside the product register the contact with the workpiece, keep the applied force constant and enable a soft landing to ensure that the part is not being over-processed while in first contact with the processing tool. The NAC can be used either as an end-of-arm tool on a robot or as a standalone component.
Please Login to see the priceNordbo Active Compensation unit
Please Login to see the price
Got a question?
Contact us quickly and easily by clicking on “Enquire Now”
Don't miss any Update
Subscribe to our newsletter and get information about latest products and trending offers.
Contact Us
Category
Menu
Solutions
Menu
Company
Menu
Resources
Menu